Powder Metallurgy hmanga thir chak tak (PM HSS) hmanga siam a ni.
BRAND: PROMISTEEL THIL THAWN THIN
GRADES: PM M4, PM T15, PM M2, PM M42, ASP 23/30/60 Equiv.
SHAPES & SIZES: Round Bar (φ10-500mm), Plate, Sheet, Near-Net ang chi te a ni
THIL THAWN DAN: HIP (Hot Isostatic Pressing), Annealed, Machine hmanga siam
MICROSTRUCTURE: Ultra-fine, Carbide sem dan inang, Non-Segregated
HARDNESS: HRC 64 - 70 (Grade atanga innghat)
THIL AWM DAN: Fine Blanking Dies, Broaches, High-Performance Milling, Cold Forming te hi a ni
MOQ: Tons 25 a ni
Powder Metallurgy hmanga thir chak tak (PM HSS) hmanga siam a ni.tool steel technology sang ber a entir a ni. Melting leh casting pangngai ang lo takin PM HSS hi a kal tlangin siam chhuah a nigas atomization a nilehA rilru a buai em em a, a rilru a hah em em bawk a. Hot Isostatic Pressing (HIP) .. Hetiang advanced process hian slow cooling phase oftraditional ingots, carbide lian tak tak, segregated tak tak siam chhuah a veng.
A result chu steel a ni a, a completelyuniform, -segregated microstructure awm lomatrix chhung zawnga insem darh ultra-fine carbides te a awm. Toolmaker leh engineer tan chuan hei hian grindability sang zawk, heat treatment laiin dimensional stability danglam tak, leh HSS pangngaiin a tih theih loh toughness sang leh wear resistance inzawmkhawm danglam tak a thlen a ni.
Products Specifications & Grade tlukpui te
PM HSS grade hrang hrang kan pe a, hei hi international standard lian ber ber (ASTM, DIN, JIS) leh proprietary grade (ASP series ang chi) nen a inang a ni.
Table-1-ah hian a awm
Application mamawh ber berte tan-performance grade sang tak tak.
PM Grade & A tlukpui hman tlanglawn |
||||
| ASTM Grade a ni | ISO Standard a ni | DIN (German ram) a ni. | JIS (Japan) chuan a rawn ti a. | A tlukpui Type |
| PM M4 a ni | HS 6-5-4 in hnehna an chang | 1.3346 | SKH54 a ni |
Wear & Toughness sang tak a ni |
| PM T15 a ni | HS chuan 10-4-3-10 in hnehna an chang | 1.3207 | SKH58 a ni |
Max Wear Resistance a ni |
| PM M2 | HS 6-5-2 in an chak | 1.3343 | SKH51 a ni |
Toughness Focused a ni |
| PM M42 a ni | HS chuan 2-9-1-8 in hnehna an chang | 1.3247 | SKH59 a ni |
Red Hardness sang tak a ni |
| PM 23-ah a awm | - | - | - |
ASP 23 nen a inang |
| PM 30 a ni | - | - | - |
ASP 30 nen a inang |
| PM 60 a ni | - | - | - |
ASP 60 nen a inang |
Table-2-ah hian a awm
Powder metallurgy hmanga alloy awm zat dik tak hmuh theih.
Chemical awm dan (Mass Fraction %) 1000 a ni. |
||||||
| Pawl | C | Cr | V | W | Mo | Co |
| PM M4 a ni | 1.42 | 4 | 4 | 5.5 | 5.25 | - |
| PM T15 a ni | 1.6 | 4 | 5 | 12 | - | 5 |
| PM M2 | 0.85 | 4.15 | 2 | 6.4 | 5 | - |
| PM M42 a ni | 1.1 | 3.75 | 1.15 | 1.5 | 9.5 | 8 |
| PM 10V a ni | 2.45 | 5.25 | 9.75 | - | 1.3 | - |
| PM S390 a ni | 1.64 | 4.8 | 5 | 10 | 2 | 8 |
Table-3-ah hian a awm
Supply Range leh Format hrang hrangte |
||
| Type hrang hrang | A zau zawng/A thuk zawng (mm) . | A zau zawng/A sei zawng (mm) . |
| Round Bars te pawh a awm | 10 mm– 500 mm inkar a ni | Customized a ni |
| Flat Bars te pawh a awm | 5 mm – 200 mm inkar a ni | 20 mm – 1000 mm inkar a ni |
| Plate te pawh a awm | 10 mm – 400 mm inkar a ni | Customized a ni |
| Sheets te pawh a awm | 1 mm – 6 mm inkar a ni | Customized a ni |
Key Features leh Advantages te
Zero Alloy hmanga inthliarna a awm
Powder a solidification chak lutuk hian chemical composition inang tlang a siam a, steel pangngaia hmuh theih chak lohna te chu a ti bo a ni.
01
Grindability tha zawk a ni
Fine carbides tih awmzia chu hmanrua te chu a sir na zawka ground theih a ni a, micro-chipping leh wheel clogging hlauhawmna a tlem zawk tihna a ni.
02
Dimensional Stability a ni
Isotropic structure hian heat treatment laiin predictable size changes a tichiang a, complex dies tan a pawimawh hle.
03
Toughness tihpun a ni
PM HSS hian HSS pangngai aiin impact load sang zawk a tuar thei a, chu chuan tool breakage a ti tlem a ni.
04
Alloy Content sang zawk a awm
PM process hian steel chu process theih lohvin Vanadium leh Cobalt content sang zawk (eg, PM 10V, PM 15V) a phalsak a ni.
05
A hman dan tlangpui
PM HSS hi HSS pangngaia a chhe emaw, a chhe emaw avanga a hlawhchhamna application-a problem-solver a ni:
Blanking & Punching tha tak tak a awm bawk
Edge retention leh toughness pawimawhna hmuna high-volume stamping dies-a hman thin.
High-Performance Cutting hmanrua te
Gear hob, broach, tap, leh end mill te hian tool life rei zawk leh cutting speed sang zawk mamawh a ni.
Cold Forming hmanrua te
Cold heading dies leh extrusion punch te hian stress nasa tak an tawk thin.
Plastic Component hmanga siam a ni
Injection molding atan chuan abrasive glass-filled plastics, chutah chuan wear resistance sang tak a ngai a ni.
FAQ
Q1: Engvangin nge PM HSS hi HSS pangngai aiin a man a to zawk?
A1: A siam chhuah dan (Atomization + HIP) hi a buaithlak zawk a, energy-intensive zawk a ni. Mahse, tool life nasa taka rei (a tam zawkah chuan 2-3x a rei zawk) leh downtime a tlem avangin total cost of ownership hi a hniam zawk fo thin.
Q2: PM M4 leh M4 pangngai hi eng nge an danglamna?
A2: Chemical lamah chuan an inang a, taksa lamah erawh an danglam thung. Conventional M4 hian carbide lian tak tak, mumal lo tak tak a nei a, chu chuan grind a ti harsa a, a chhe thei bawk. PM M4 hian carbide tha tak tak, uniform tak tak a nei a, hei hian a ti khauh zawk a, machine/grind pawh a awlsam zawk bawk.
Q3: PM HSS hi coated theih a ni em?
A3: Ni e, PM HSS hi PVD coatings (TiN, TiAlN) atan substrate tha tak a ni a, a chhan chu a surface quality inang tlang hian HSS pangngai aiin adhesion tha zawk a siam thei a ni.
Q4: ASP 23 emaw ASP 30 emaw nen hian eng grade nge tehkhin theih?
A4: ASP series lar tak nena chemical composition leh property inang PM grade kan supply a, powder metallurgy application atan high-performance alternative kan pe a ni.
hot tags .: powder metallurgy high speed steel (pm hss), China powder metallurgy high speed steel (pm hss) siamtute, supplier te an ni
I duh ve mai thei bawk.
Inquiry thawn rawh .